|
Post by eric on Nov 3, 2007 20:51:16 GMT 1
Oooo, Velcro! Brilliant idea, it'll hold them firmly, and be easy enough to remove them from.
Simple....when you know how!
Thanks again Markus.
eric.
|
|
|
Post by bob on Nov 25, 2007 19:36:34 GMT 1
Hi Markus on the German preview site there seems to be instructions for installing the radio gear supplied by Hatchette obviously in german. There seems to be a section showing a piece of wood with parts for the A frame support for the prop shafts. Do you know if that particular part comes with one of the weekly issues or is part of the kit. Also the instructions are they also part of the kit. It would be useful if we could get a copy of that template to make our own supports.
|
|
|
Post by markus on Nov 25, 2007 21:14:00 GMT 1
Hi Markus on the German preview site there seems to be instructions for installing the radio gear supplied by Hatchette obviously in german. There seems to be a section showing a piece of wood with parts for the A frame support for the prop shafts. Do you know if that particular part comes with one of the weekly issues or is part of the kit. Also the instructions are they also part of the kit. It would be useful if we could get a copy of that template to make our own supports. hi bob ! these (not good looking) wooden parts are only for use with amati's 6mm propshafts the scale parts will come with the regular issues. i think they'll be made of resin. these parts should allow a 4mm hole to fit 'our' small propshafts... markus
|
|
|
Post by russ on Dec 6, 2007 14:01:51 GMT 1
I am assuming that when hatachette are sending these controll gear out they are all different crystals cause some companys send them all the same if this th4e case then if any of us sailing neer each and other disaster we be trying to take each others boats
|
|
|
Post by markus on Dec 6, 2007 17:32:08 GMT 1
I am assuming that when hatachette are sending these controll gear out they are all different crystals cause some companys send them all the same if this th4e case then if any of us sailing neer each and other disaster we be trying to take each others boats that's right - but i'm afraid all radio controls may be delivered with the same frequency... eventually crystals can be changed, but i can't find a crystal slot on the photo of their transmitter markus
|
|
|
Post by Mark on Dec 6, 2007 23:58:26 GMT 1
If it's anything like their RCcars, the R/C sets go out with random crystals in, but they can be changed.
|
|
|
Post by viking on Dec 17, 2007 17:19:12 GMT 1
having more than one boat i have gone for a spektrum DX7 2.4gig expensiv but well werth it.All to gether i have ten ships when the biss is dun.No nead for pegs or runing around to find the one on the same chanel as you just go to th pond and sail. ;D
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 21, 2008 4:45:44 GMT 1
Starting to think about the drive system from Markus, only thing is I'm not sure about modifying the hull, (since it's up to part 10 and has been built as per instructions). How hard / easy would it be, think I would have to do some drilling or cutting with the hull supported somehow ?
Also what would the cost be for sending to AU ?
|
|
|
Post by eric on Jan 21, 2008 13:49:53 GMT 1
Skyfire, are you thinking of the two or three motor setup?
Much less work has to be done for the two motor version. If you follow this thread from the very start (I know it is really long) you will see what is involved with converting the hull for the full three motor setup.
|
|
|
Post by markus on Jan 21, 2008 18:06:50 GMT 1
Starting to think about the drive system from Markus, only thing is I'm not sure about modifying the hull, (since it's up to part 10 and has been built as per instructions). How hard / easy would it be, think I would have to do some drilling or cutting with the hull supported somehow ? Also what would the cost be for sending to AU ? eric is right, there's a lot to read prices include shipping to australia as uninsured parcel (30-35 days for delivery) shipping as insured parcel is 20 euro (only 10-14 days for delivery)
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 22, 2008 1:38:15 GMT 1
Skyfire, are you thinking of the two or three motor setup? I was thinking about the 3 motor setup, but it might just have to be the 2 motor setup. I've read right through the thread several times. The modifications seem to be done before the parts are fitted. Can the modifications still be done with the hull as it is below ?
|
|
|
Post by markus on Jan 22, 2008 7:42:34 GMT 1
the mods can still be done (if you own a dremel with a cutting-disk)
take a look at don's how-to....he made it after having partly planked..
markus
|
|
|
Post by nickjames54 on Jan 22, 2008 21:42:58 GMT 1
Hi Markus, I am new to this forum and I would like to know if you can still supply the drive parts regards, Nick
|
|
|
Post by markus on Jan 22, 2008 21:56:42 GMT 1
Hi Markus, I am new to this forum and I would like to know if you can still supply the drive parts regards, Nick of course, just pm me what you need and i will get it for you.... markus
|
|
|
Post by david on Jan 24, 2008 0:29:07 GMT 1
|
|